Learning how to connect Sony Bluetooth headphones to Mac is simple. You can pair Sony Bluetooth headphones with a MacBook or a desktop Mac in a few minutes, with no extra software and no cable.
This guide works for compatible Sony WH, WF and other Sony Bluetooth models. The exact button you press to start pairing depends on your model, so check the section for your headphones below if the first steps do not work.
How to Connect Sony Bluetooth Headphones to a Mac
Follow these four steps to connect Sony headphones to a MacBook or any other Mac. Do them in order, and keep your headphones close to your Mac while you pair them.
Step 1: Put Your Sony Headphones in Pairing Mode
Charge your headphones first, then turn them on. When you turn on a new pair of Sony headphones for the first time after purchase, they usually enter pairing mode on their own. You will hear a voice guide or see a flashing light that shows they are ready to pair.
If your headphones have been paired before, you need to start pairing mode by hand. Follow the instructions for your model in the section below. For example, on the Sony WH-1000XM5 you hold the Power button for about 5 seconds until you hear the voice guide say “Pairing.”
If pairing is not finished within 5 minutes, pairing mode is canceled. Turn the headphones off and start again. Sony also gives a general pairing procedure for Mac OS devices on its support site.
Step 2: Open Bluetooth Settings on Your Mac
Open the Sony headphones Mac Bluetooth settings on your Mac:
- Click the Apple menu in the top-left corner of the screen.
- Click System Settings.
- Click Bluetooth in the sidebar.
- Make sure Bluetooth is turned on. If it is off, click the switch to turn it on.
Leave this Bluetooth window open while you finish the next step. Your Mac can only find your headphones while they are in pairing mode.
Step 3: Find and Connect Your Sony Headphones
Look in the list of available devices on the Bluetooth settings page. You should see your Sony model name, for example WH-1000XM5, WH-1000XM4 or WF-1000XM5. Click Connect next to the model name.
Wait a few seconds. When the headphones connect, the status next to the model name changes to Connected. You should also hear a sound or a voice guide in the headphones that confirms the connection.
Step 4: Enter the Passcode If Required
Most of the time, your Mac will not ask for a passcode. If it does ask for one, enter 0000. That is the passkey Sony uses for its Bluetooth headphones.
After you enter the passcode, the headphones should connect. If the connection fails, turn the headphones off, turn them back on, put them in pairing mode again, and repeat Step 3.
How to Set Sony Headphones as the Default Audio Device
After your Sony headphones connect, your Mac should play sound through them. If it does not, check the sound settings.
Change Sound Output Settings
- Click the Apple menu, then click System Settings.
- Click Sound in the sidebar.
- Click the Output tab.
- Click your Sony headphones in the list of output devices.
Apple explains the same steps in its guide to change the sound output settings on Mac. You can also click the speaker icon in the menu bar and pick your Sony headphones there.
Select the Sony Microphone for Calls
If you want to use your Sony headphones for calls, check the input settings too. Go to System Settings > Sound > Input and select your Sony microphone if it is listed. If it is not listed, your headphones may not offer a microphone to your Mac, or they may need to be reconnected.
How to Connect Different Sony Headphone Models to a Mac
The steps on your Mac are the same for every model. What changes is how you put the headphones in pairing mode. Use the instructions for your model below, and check your model’s own Sony help guide if you are not sure.
Sony WH-1000XM5
For a Sony WH-1000XM5 Mac connection, turn the headphones on. The first time you turn them on after purchase, they enter pairing mode on their own. To pair them with a second device, hold the Power button for about 5 seconds until the voice guide says “Pairing.” Then find WH-1000XM5 in your Mac Bluetooth settings and click Connect. See Sony’s WH-1000XM5 guide for pairing with a Mac.
Sony WH-1000XM4
For Sony WH-1000XM4 Bluetooth pairing, turn the headphones on. The first time you turn them on after purchase, they enter pairing mode on their own. To pair them with a second device, press and hold the Power button for about 7 seconds until the voice guide says “Pairing.” Then find WH-1000XM4 in your Mac Bluetooth settings and click Connect. See Sony’s WH-1000XM4 guide for pairing with a Mac.
Note that the 7-second hold is for the XM4. Do not use it as a rule for every Sony model. The XM5, for example, uses about 5 seconds.
Sony WF-1000XM5
The WF-1000XM5 are earbuds, so the pairing button is on the charging case, not on the earbuds. The first time you use them, take the earbuds out of the case and they enter pairing mode on their own. To pair them with a second device, put the earbuds in the case, leave the lid open, and press and hold the pairing button on the back of the case for about 5 seconds or more until the indicator flashes blue twice in a row. Then find WF-1000XM5 in your Mac Bluetooth settings and click Connect. See Sony’s WF-1000XM5 guide for pairing with a Mac.
Sony WH-CH Series
The WH-CH series includes lower-cost over-ear models such as the WH-CH720N. The first time you turn them on after purchase, they enter pairing mode on their own. To pair a WH-CH720N with a second device, press and hold the Power button for about 5 seconds or more until the voice guide says “Pairing.” Then find the model name in your Mac Bluetooth settings and click Connect. See Sony’s WH-CH720N guide for pairing with a Mac. Other WH-CH models may use a different button or hold time, so check your own model’s Sony help guide.
If you are still choosing a pair, see our guide to the best Sony noise-cancelling headphones.
How to Switch Sony Headphones Between Your Mac and Phone
Some Sony models support multipoint, which means they can stay connected to two devices at the same time, such as your Mac and your phone. On those models, you can switch by playing sound on the other device. Not every Sony model supports multipoint, so check your model’s guide first.
On models without multipoint, you need to disconnect from one device before you connect to the other. Turn off Bluetooth on the device your headphones are now connected to, or disconnect the headphones in that device’s Bluetooth settings. Then go to your Mac Bluetooth settings and click Connect next to your Sony headphones. Do not choose Forget This Device or Unpair unless you want to remove the headphones from that device completely. Sony explains this in its guide to switching between Bluetooth devices.
Why Won’t My Sony Headphones Connect to My Mac?
If your Sony headphones are not connecting to your Mac, work through the problems below. Most of them have a simple fix.
My Sony headphones are not showing up on my Mac
First, make sure the headphones are in pairing mode. If they are already connected to your phone, your Mac may not see them. Turn off Bluetooth on your phone, then put the headphones in pairing mode again. Also check that Bluetooth is on in your Mac settings, and that the headphones are charged and close to your Mac. If the list still does not show them, restart your Mac and try again.
My Mac keeps connecting to my phone instead
Headphones often reconnect to the last device they were used with. Turn off Bluetooth on your phone, or disconnect the headphones in your phone’s Bluetooth settings. Then click Connect next to your Sony headphones in your Mac Bluetooth settings. On models that support multipoint, the headphones can stay connected to both devices, so this problem is less likely.
My Mac connects but no sound plays
Go to System Settings > Sound > Output and select your Sony headphones. If they are already selected, turn the volume up and play a test sound. If sound still comes from your Mac speakers, disconnect the headphones in Bluetooth settings and connect them again.
The LE device appears instead of the headphone name
On the WH-1000XM4, you may see two entries in the Bluetooth list: WH-1000XM4 and LE_WH-1000XM4. Choose the standard WH-1000XM4 entry, not the LE_WH-1000XM4 entry. The LE entry can appear first, and the standard entry can take 30 to 60 seconds to appear, so wait before you give up. Sony states this in its WH-1000XM4 pairing guide.
The connection keeps disconnecting
Move closer to your Mac and keep the headphones away from other Bluetooth devices, Wi-Fi routers and microwaves, which can cause interference. Make sure the headphones are charged. If the problem continues, remove the headphones from your Mac Bluetooth settings, restart both devices, and pair them again. If Bluetooth is not working at all on your Mac, see our guide on how to fix Bluetooth not available on Mac.
Does Sony LDAC Work on Mac?
No, not in the way many people expect. Some Sony headphones support LDAC, but LDAC is not supported natively on macOS. When you connect Sony headphones to a Mac, macOS Bluetooth audio generally uses SBC or AAC instead.
The Sony Sound Connect app does not add LDAC support to macOS, so installing the app will not change the codec your Mac uses. You can still use your Sony headphones on a Mac, and they will sound fine, but you will not get LDAC on macOS.
Frequently Asked Questions
Can I connect Sony Bluetooth headphones to a MacBook?
Yes. Put your Sony headphones in pairing mode, open System Settings > Bluetooth on your MacBook, and click Connect next to your Sony model name. If your Mac asks for a passcode, enter 0000.
Why are my Sony headphones not showing up on my Mac?
They are probably not in pairing mode, or they are already connected to your phone. Put them in pairing mode again, turn off Bluetooth on your phone, and check that Bluetooth is on in your Mac settings.
What is the passcode for Sony Bluetooth headphones?
The passcode is 0000. Enter it if your Mac asks for a passkey when you pair your Sony headphones.
Can I connect Sony headphones to two devices?
Only on models that support multipoint. On those models, your headphones can stay connected to two devices at once. On other models, disconnect from one device before you connect to the other.
How do I disconnect Sony headphones from my Mac?
Go to System Settings > Bluetooth, find your Sony headphones in the list, and click Disconnect. To remove them completely, click the small information icon next to the headphones and choose Forget This Device.
Why is sound still coming from my Mac speakers?
Your Mac is still using its built-in speakers for sound output. Go to System Settings > Sound > Output and select your Sony headphones. Then check the volume and play a test sound.

